Why not just mix them over so they dont clip? Why the bleep would you want to have music that clips get mastered. All your doing is making already distorted audio, sound even worse by mastering.

quote:

Don't think of it as me asking for something, think of it as practice for you.

Yah, practice messing up their ears?


protip : always leave a few dbfs of headroom when mixing, you don't need to be anywhere near clipping if your working on a DAW.

___________________
_____________________________________
commercial and underground electronic music (house/techno/trance/other) will surpass today's hip hop/pop/rock/country in worldwide interest...if it has'nt already.

Because the only thing that exists for them are the mp3 renders I did. They are for the most part from a studio I no longer have.

And there isn't much distortion, in fact I only noticed distortion in some of them after they were mastered lol. Some of them are very loud. So I needed the RMS averaged out. The only reason I'm mastering the clipped ones is because clipping, even if there is no distortion, breaks speakers.

Also the ones that clip are from 6 years ago before I knew what clipping was. One of the tracks is basically a phat brick.

___________________
i'm the alchemist without the cyst without a doubt out of the mist
dig out the grout expose the pest to take it out without the rest

they will attest my patients restorations from the best

i'm from the west i'm not an acmeist only the alchemist

once the dynamics are out, you'll never get them back.

___________________
Analogue Mastering
Esoteric sound for the discerning ear

Yeah, the trick is to reduce clipping without loosing them

___________________
i'm the alchemist without the cyst without a doubt out of the mist
dig out the grout expose the pest to take it out without the rest

they will attest my patients restorations from the best

i'm from the west i'm not an acmeist only the alchemist

your clipped track is 0,0db, take a limiter en put it on -0.03db and run your track through that, or normalize them * .997% loudness

___________________
Analogue Mastering
Esoteric sound for the discerning ear

quote:

Originally posted by Raphie your clipped track is 0,0db, take a limiter en put it on -0.03db and run your track through that, or normalize them * .997% loudness

I don't know how to do that. I have Audacity if that helps

___________________
i'm the alchemist without the cyst without a doubt out of the mist
dig out the grout expose the pest to take it out without the rest

they will attest my patients restorations from the best

i'm from the west i'm not an acmeist only the alchemist

quote:

Originally posted by cronodevir Yeah, the trick is to reduce clipping without loosing them

have you tried increasing your latency ? Maybe that might help the quality issues. Also, there is a plugin that acts someone like a compressor except it is triggered by suckyness. It has an incredibly fast attack but don't get caried away with the threshold setting or your music will most likely just be silence.

Last edited by RichieV on Apr-26-2009 at 00:20

quote:

Originally posted by RichieV have you tried increasing your latency ? Maybe that might help the quality issues. Also, there is a plugin that acts someone like a compressor except it is triggered by suckyness. It has an incredibly fast attack but don't get caried away with the threshold setting or your music will most likely just be silence.

He could always offset the latency with a little bit of pre-delay. It might also help to add bit-reduction to the mastering suite.

quote:

Originally posted by RichieV have you tried increasing your latency ? Maybe that might help the quality issues. Also, there is a plugin that acts someone like a compressor except it is triggered by suckyness. It has an incredibly fast attack but don't get caried away with the threshold setting or your music will most likely just be silence.

Maby I should use the soundgoodizer?

Excerpt from the FLStudio Manual: [I didn't change a single letter]

"

* The knob - Blends from left to right from Soungoodizing 0% (bad) to 100% (good). Turn the knob to the level that sounds goodest.


* Parameters (A, B, C, D) - Click the switches to select one of 4 carefully chosen, hand crafted phase-locked hyper-calibrated bit-polished Maximus presets. Select the preset to match your music by clicking and listening for the good stuff to happen.
"

___________________
i'm the alchemist without the cyst without a doubt out of the mist
dig out the grout expose the pest to take it out without the rest

they will attest my patients restorations from the best

i'm from the west i'm not an acmeist only the alchemist

quote:

Originally posted by cronodevir Maby I should use the soundgoodizer? Excerpt from the FLStudio Manual: [I didn't change a single letter] " * The knob - Blends from left to right from Soungoodizing 0% (bad) to 100% (good). Turn the knob to the level that sounds goodest. * Parameters (A, B, C, D) - Click the switches to select one of 4 carefully chosen, hand crafted phase-locked hyper-calibrated bit-polished Maximus presets. Select the preset to match your music by clicking and listening for the good stuff to happen. "

Unfortunately you can't make something from nothing. You can however take away something that isn't good as i discussed prior. My only worry is that the end result will have an rms of -infinity

quote:

Originally posted by RichieV Unfortunately you can't make something from nothing. You can however take away something that isn't good as i discussed prior. My only worry is that the end result will have an rms of -infinity

Trying to be slick ey? I do get your implication.

Take away the bad parts......will have no sound.... ha, ha. no.

___________________
i'm the alchemist without the cyst without a doubt out of the mist
dig out the grout expose the pest to take it out without the rest

they will attest my patients restorations from the best

i'm from the west i'm not an acmeist only the alchemist