i know what a vapo is, i have used two, you just need the right heat ont eh stove, and you can do it
Mar-25-2003 00:22
TeKnoHe@d2025
Derek Howell Addict
Registered: Jan 2001
Location: Pittsburgh, Pennsylvania
Why don't you just go out and buy one ya cheap bastard Really though, they couldn't be all that expensive. I guess you could put a pan of water infront of your register where the heat comes out from your furnace though...
man.. making drugs ain't for amateurs.. my 3 blown off fingers can vouch for that..
___________________
Cause back before '99, U didn' give a damn about PvD, but now that he's pressin' platinum LP's, all of a sudden ur' into
his killer beat's! Ain't nothin' U can do to make it stop cause trance makes the world go round, so cut the act...
1 milk bottle
1 tube of pringles
1 tealight candle
some grass/hash
get the pringle tube and cut off the bottom end so that you have the metal cover and about 4-5 inches of tube.
get the milk bottle and somehow crack the bottom off so that you have a bottomless milk bottle (careful not to cut yourself, maybe a glass saw or something to make it ultra clean)
once you have done this light the candle and place the tube over the top, then leave for about 30 mins for the metal to heat up..
now chuck your stash on, put the bottle over the tube and enjoy
(if you dont wanna suck from the top of the bottle then attach a tube to the lid or somethin )
___________________
Keep it clean,
Keep it green..
These are my plans for building a nice vaporizer. They are based on the vaporizer described in the file Vaporizer Principals . The main differences being that this file will be a little less in depth on the actual assembly (I think you know how to drill holes) and will be a bit more in depth on the bowl making etc.
A soldering iron
Flat piece of wood (any wood about 1/2 inch thick...at least 8 inches X 8 Inches)
Wooden Dowels (long at least 22 inches and about 1/2 inch diameter)
A plastic 2 liter bottle (the kind with the black part on the bottom)
First cut the flat wood into a triangle with equal 8 inch sides (60 deg. angles)
Second Stain and varnish the wood (or polyurethane)
Choose one side of the flat triangle to be the top
Find the exact center of the triangle and mark it on both top and bottom
Choose a drill bit size such that the soldering iron handle can be set into the hole created by the drill and have the rim on the top (handle end nearest the element)sit on it (so it don't fall through)
Drill with this size bit through the center of the triangular piece
Turn the triangular piece over and mark 3 spots each about 1 inch from the vertex each angle
Drill through each of these at a 15 degree angle with the smallest bit that the size dowel you have will fit into (snug is good)
Turn the triangular piece to the top
Pull the plastic bottom piece off of the 2 liter bottle
Cut out the middle of this piece (the indented middle part)
Place the black piece over the hole in the center of the wooden triangle and put a two nails through it into the wood
Use Hot Glue (or better Silicon sealant) around the bottom of the black piece ..and fill in any cracks in it made in the removal from the bottle
Place some wood glue in each of the holes on the bottom of the triangular piece.
Put a dowel in each of these holes and gently tap them with a hammer to set them (then let the glue dry)
Put the soldering iron power cord through the hole in the middle (trim the plastic if you have to)
Pull the soldering iron through so that it rests on the base...sticking up into the air
Cut out the bottom of the 2 liter bottle (make a nice hole...as big as you can but so that it still will go into the black piece and fit (leave some of the curved bottom)
That’s it...now just fashion a bowl and your all set
Fashioning the bowl
Depending on what soldering iron you use the bowl making is a little different. I usually use a more expensive iron where the tip screws on. It has the threads on the element (like a screw) and the soldering tip had threads like a nut (inside).
when this type is used the bowl is easy to make. There are two ways I have had success with. The first is Tin foil. Just wrap tin foil around the threads where the tip would go and make a little bowl (small bowl is good...like maybe 1/2 an inch diameter)
The next way to make a bowl for this type is to buy a thimble (size 9 works nice). It must be a metal thimble! Take the timble and make a hole in it (the top) work the hole till it is the size of the threads on the soldering iron. Now try to put it on. If it is too loose then take it off and wrap a few layers of tin foil around the threads and try again (this will tighten it up)
If you use the cheaper soldering irons (the ones where the tip screws in rather than on) then try leaving the tip on and using a larger thimble (much larger).
Using the vaporizer
Pack the bowl with herb (pack it good)
Put the bottle over the soldering iron and place it in the black piece
Plug it in
Watch carefully and as soon as you see a white cloud coming up unplug it (else it will get too hot and burn the herb)
wait for it to build up
Unscrew the cap
Push up on the soldering iron (from the handle) and Hit
replace cap and iron
Let it fill
Hit again
Unpack with tweezers and repack (the bowl is small so ya have to repack allot)
Notes:
Initial warm up can take up to 5 min
Plug in the iron and leave it on (uncovered and not packed) for a while before first use (you will see why)
You may need to pack it 3 or 4 times for 1 joints worth but I have seen 3 people get stoned off their asses with this little bit (I could not stand after that)
If the bottle is deforming from the heat then it is too hot (don't leave it on so long)
Enjoy!
hehe
Really though, they couldn't be all that expensive. I guess you could put a pan of water infront of your register where the heat comes out from your furnace though...
)
