 |
|
|
|
 |
DJ Tranz
Mafiya Beatts
Registered: Feb 2003
Location: SoCal --- LATA # 99
|
|
|
| quote: | Originally posted by g-money
Cool Price is not the problem but just looking for something thats 200 watts a side. |
Crown amp all the way
XLS402
Performance:
Sensitivity (volts RMS) for full rated power at 4 ohms:
XLS-402: 1.025V
Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.75 dB.
Phase Response (degrees at 1 watt):
at 10 Hz: –10.
at 20 kHz: +19.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power: > 100 dB.
No weighting, below rated power: > 95 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 1 kHz: < 0.5%.
Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200. Crosstalk (below rated power)
at 1 kHz: –82 dB.
at 20 kHz: –58 dB.
Voltage Gain (at maximum output): 31 dB.
Output Power per channel: 570w at 2ohm, 400w at 4ohm, 260w at 8 ohm
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms per channel in Stereo, 8 ohms in Bridge Mono.
AC Line Voltage and Frequency Configurations Available (±10%): 120VAC/60 Hz and 230VAC/50 Hz.
Controls:
Level: Two front-panel, black rotary level controls, one for each channel.
Power: Front-panel switch; on when in the UP position.
Circuit Breaker: Provides overload protection. Indicators
Clip: Two front-panel red LEDs, one for each channel, illuminate when the channel’s output signal is being overdriven.
Power: Green front-panel LED indicates amplifi er has been turned on and AC power is available.
Fault: Yellow front-panel LED illuminates when amplifi er is in protect mode. Also illuminates briefl y during normal power-up when amplifi er is fi rst switched on.
Input/Output:
Input Connectors: One per channel; backpanel three-pin female XLR input connectors.
Input Impedance (nominally balanced, nominally unbalanced): 20 k ohms, 10 k ohms.
Output Connectors: One 4-pole Speakon® connector and one pair of back-panel, 5-way binding posts per channel; accepts banana plugs, spade lugs or bare wire. (European models do not accept banana plugs.)
DC Output Offset (shorted input): ±10 millivolts.
Output Signal: Stereo, unbalanced, two-channel.
Protection:
XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and special thermal protection for the unit’s transformers.
Construction:
Ventilation: Flow-through ventilation from front to back.
Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 14-inch (35.6-cm) depth behind the mounting surface.
Net Weight:
XLS-402: 25.3 lbs. (11.5 kg)
The CE-Series of Crown amplifiers are professional tools designed and built for professional use. Engineered and manufactured by the same teams who built Crown’s acclaimed Macro-Tech® and KSeries amps, the CE 1000 has the rugged heart and soul that have characterized Crown’s amplifiers for over 30 years. With many of the same controls and features you’ve come to expect from Crown, CESeries amplifiers feature front-panel detented level controls, useful function indicators, proportional fan-assisted cooling, shortcircuit protection and more.
For superior flexibility, Crown CE-Series amplifiers can work with a range of Crown SST (System Solution Topologies) modules which provide true professional features like fixed-point crossover and summed bass output.
With a powerful, reliable performance, CESeries amps easily handle real 2-ohm loads and are capable of chest-thumping lows. Plus, your investment in an CE-Series amplifier is backed by Crown’s unequaled Three- Year, No-Fault, Fully Transferable Warranty that covers everything.
Features
Accurate, uncolored sound with very low distortion for the best in music and voice reproduction.
Bridge-mono/stereo mode switch allows you to set up your amps/speakers in the configuration that best suits your needs.
Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, highfrequency overloads and internal faults.
Extremely versatile, handling a wide range of speaker impedances and outputs.
Switchable input sensitivity.
Proportional speed fan optimizes cooling efficiency.
Shallow rack depth. Only 12.25 inches deep!
Choice of Speakon®, binding post, or barrier strip outputs (Speakon® comes standard).
Choice of balanced 1/4-inch (6.35-mm), XLR, or barrier strip inputs.
The best Three-Year, No-Fault, Fully Transferable Warranty in the business! It even covers round-trip ground shipping in the U.S. for all warranty work.
Specifications: Note: All measurements relate to 120-volt, 60-Hz units in Stereo mode with 8-ohm loads and an input sensitivity of 26- dB gain at 1-kHz rated power unless otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies.
Load Impedance: Safe with all types of loads. Rated for 2, 4 and 8 ohms in Stereo mode, 4 and 8 ohms in Bridge-Mono mode.
Voltage Gain to 1-kHz, 8-ohm rated output: 30.5-dB gain at 1.4-volt sensitivity; 26-dB gain at 2.34-volt sensitivity.
Required AC Mains: 50/60 Hz (North American units are 60 Hz only); 100-, 120- and 230-/240-VAC (±10%) units are available.
AC Line Current,100 Volts: 7.6 A;120 Volts: 6.3 A; 230-240 Volts: 3.5 A;
At Idle: All amps draw no more than 90 watts.
AC Line Connector: NEMA 5-15P (15 A).
Performance:
Frequency Response: ±0.2 dB from 20 Hz to 25 kHz at 1 watt.
Phase Response: ±15 degrees from 20 Hz to 20 kHz at 1 watt.
Signal to Noise Ratio,
A-Weighted: Better than 105 dB below rated 1-kHz power; 20 Hz to 20 kHz: Better than 100 dB below rated 1-kHz power.
Total Harmonic Distortion (THD): 0.5% or less true THD from 20 Hz to 20 kHz.
Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) Less than 0.1% at rated power to 35 dB below rated power at 8 ohms.
Damping Factor: Better than 400 from 10 Hz to 400 Hz.
Crosstalk: Greater than 55 dB below rated power, 20 Hz to 20 kHz.
Common Mode Rejection (CMR): Better than 70 dB from 20 Hz to 1 kHz.
DC Output Offset (Shorted Input): ±10 mV.
Controls and Connectors:
Level: A detented rotary level control for each channel located on the front panel.
Power: An on/off rocker switch located on the front panel.
Mode: A two-position switch located on the back panel below the input connectors which, when turned to stereo, operates the amplifier as two independent channels. When “Bridge- Mono” mode is selected, the amplifier bridges the two output channels for twice the output voltage.
Reset: A front-panel push button used to reset the circuit breaker that protects the power supply.
Sensitivity: A two-position switch located on the back panel next to the Mode switch. Switchable between 1.4 volts for full output into an 8-ohm load (default setting), or a fixed voltage gain of 26 dB. 0.775-volt sensitivity available as a Service Option.
Fault Jack: A back-panel RJ-11 jack that may be remotely monitored to signal amplifier
Fault condition. An LED or other signalling device (not supplied) may be used.
Indicators: (all located on front panel)
Signal: A green LED for each channel which flashes when a very low-level signal (>–40 dBm) is present at input. May be used for troubleshooting cable runs.
Clip: A red LED for each channel which turns on when distortion becomes audible in the amplifier output.
Input/Output:
Input Connector (standard module): One Neutrik® Combo connector for each channel which features a balanced ¼-inch (6.35-mm) phone jack and a 3-pin female XLR connector, in parallel with a barrier strip termination.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance: Nominally 20 k ohms, balanced. Nominally 10 k ohms, unbalanced.
Input Sensitivity: 1.4 volts for standard 1-kHz power, or fixed 26-dB gain. 0.775-volt sensitivity available as a Service Option.
Output Connectors:
Two Neutrik® Speakon® NL4MP (mates with NL4FC) output connectors.
Optional 5-way binding post or barrier strip outputs (in parallel with Speakon® connectors) are available.
DC Output Offset: ±10 millivolts. Output Signal,
Stereo: Unbalanced, two-channel;
Bridge-Mono: Balanced, single-channel. Channel 1 controls are active; Channel 2 should be turned down.
Protection:
CE-Series amplifiers are protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; input overload damage; and high-frequency blowups. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients.
560w at 2ohm, 450w at 4ohm, 275w at 8ohm
Crown MA602
The Macro-Tech VZ Series represents the latest breakthrough in Crown's unending quest to deliver the most power in the smallest package.
The Macro-Tech 3600VZ packs 3,600 watts into a mere 3.5 inches of vertical rack space. The Macro-Tech 5002VZ packs an incredible 5,000 watts into little more than 5 inches of vertical rack space.
400w at 2 ohm, 325w at 4ohm, 225w at 8ohm
Crown K1
No Fan No Noise
Patented BCATM Circuit Design
Unmatched Thermal Efficiency
Superior Energy Efficiency
Sealed Chassis
Superior Sound
Modular Design and Construction for Quick Service
TLC -Thermal Level Control Protection Subtly and Dynamically Reduces Gain As Needed
Automatic Turn-On Diagnostics
Significantly Less Component Degrading Heat Generated
Recessed, Detented Level Controls
750w at 2ohm, 550w at 4ohm, 350w at 8 ohm
___________________
Daniel, aka DJ Tranz(MafiyaBeatts-LA,SF)
Rest In Peace Adam 'STARKID' Spears,Thank You For Your Wonderful Music That Will Live On Forever, RIP Buddy...
www.mafiyabeatts.com Vote for Tranz @ The DJ List!
|
|
 Apr-04-2003 18:47 
|
|
|
|
|
Phu
Mix Master
Registered: Oct 2000
Location: Vancouver
|
|
|
| quote: | Originally posted by DJ Tranz
Crown amp all the way
XLS402
Performance:
Sensitivity (volts RMS) for full rated power at 4 ohms:
XLS-402: 1.025V
Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.75 dB.
Phase Response (degrees at 1 watt):
at 10 Hz: –10.
at 20 kHz: +19.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power: > 100 dB.
No weighting, below rated power: > 95 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 1 kHz: < 0.5%.
Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200. Crosstalk (below rated power)
at 1 kHz: –82 dB.
at 20 kHz: –58 dB.
Voltage Gain (at maximum output): 31 dB.
Output Power per channel: 570w at 2ohm, 400w at 4ohm, 260w at 8 ohm
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms per channel in Stereo, 8 ohms in Bridge Mono.
AC Line Voltage and Frequency Configurations Available (±10%): 120VAC/60 Hz and 230VAC/50 Hz.
Controls:
Level: Two front-panel, black rotary level controls, one for each channel.
Power: Front-panel switch; on when in the UP position.
Circuit Breaker: Provides overload protection. Indicators
Clip: Two front-panel red LEDs, one for each channel, illuminate when the channel’s output signal is being overdriven.
Power: Green front-panel LED indicates amplifi er has been turned on and AC power is available.
Fault: Yellow front-panel LED illuminates when amplifi er is in protect mode. Also illuminates briefl y during normal power-up when amplifi er is fi rst switched on.
Input/Output:
Input Connectors: One per channel; backpanel three-pin female XLR input connectors.
Input Impedance (nominally balanced, nominally unbalanced): 20 k ohms, 10 k ohms.
Output Connectors: One 4-pole Speakon® connector and one pair of back-panel, 5-way binding posts per channel; accepts banana plugs, spade lugs or bare wire. (European models do not accept banana plugs.)
DC Output Offset (shorted input): ±10 millivolts.
Output Signal: Stereo, unbalanced, two-channel.
Protection:
XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and special thermal protection for the unit’s transformers.
Construction:
Ventilation: Flow-through ventilation from front to back.
Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 14-inch (35.6-cm) depth behind the mounting surface.
Net Weight:
XLS-402: 25.3 lbs. (11.5 kg)
The CE-Series of Crown amplifiers are professional tools designed and built for professional use. Engineered and manufactured by the same teams who built Crown’s acclaimed Macro-Tech® and KSeries amps, the CE 1000 has the rugged heart and soul that have characterized Crown’s amplifiers for over 30 years. With many of the same controls and features you’ve come to expect from Crown, CESeries amplifiers feature front-panel detented level controls, useful function indicators, proportional fan-assisted cooling, shortcircuit protection and more.
For superior flexibility, Crown CE-Series amplifiers can work with a range of Crown SST (System Solution Topologies) modules which provide true professional features like fixed-point crossover and summed bass output.
With a powerful, reliable performance, CESeries amps easily handle real 2-ohm loads and are capable of chest-thumping lows. Plus, your investment in an CE-Series amplifier is backed by Crown’s unequaled Three- Year, No-Fault, Fully Transferable Warranty that covers everything.
Features
Accurate, uncolored sound with very low distortion for the best in music and voice reproduction.
Bridge-mono/stereo mode switch allows you to set up your amps/speakers in the configuration that best suits your needs.
Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, highfrequency overloads and internal faults.
Extremely versatile, handling a wide range of speaker impedances and outputs.
Switchable input sensitivity.
Proportional speed fan optimizes cooling efficiency.
Shallow rack depth. Only 12.25 inches deep!
Choice of Speakon®, binding post, or barrier strip outputs (Speakon® comes standard).
Choice of balanced 1/4-inch (6.35-mm), XLR, or barrier strip inputs.
The best Three-Year, No-Fault, Fully Transferable Warranty in the business! It even covers round-trip ground shipping in the U.S. for all warranty work.
Specifications: Note: All measurements relate to 120-volt, 60-Hz units in Stereo mode with 8-ohm loads and an input sensitivity of 26- dB gain at 1-kHz rated power unless otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies.
Load Impedance: Safe with all types of loads. Rated for 2, 4 and 8 ohms in Stereo mode, 4 and 8 ohms in Bridge-Mono mode.
Voltage Gain to 1-kHz, 8-ohm rated output: 30.5-dB gain at 1.4-volt sensitivity; 26-dB gain at 2.34-volt sensitivity.
Required AC Mains: 50/60 Hz (North American units are 60 Hz only); 100-, 120- and 230-/240-VAC (±10%) units are available.
AC Line Current,100 Volts: 7.6 A;120 Volts: 6.3 A; 230-240 Volts: 3.5 A;
At Idle: All amps draw no more than 90 watts.
AC Line Connector: NEMA 5-15P (15 A).
Performance:
Frequency Response: ±0.2 dB from 20 Hz to 25 kHz at 1 watt.
Phase Response: ±15 degrees from 20 Hz to 20 kHz at 1 watt.
Signal to Noise Ratio,
A-Weighted: Better than 105 dB below rated 1-kHz power; 20 Hz to 20 kHz: Better than 100 dB below rated 1-kHz power.
Total Harmonic Distortion (THD): 0.5% or less true THD from 20 Hz to 20 kHz.
Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) Less than 0.1% at rated power to 35 dB below rated power at 8 ohms.
Damping Factor: Better than 400 from 10 Hz to 400 Hz.
Crosstalk: Greater than 55 dB below rated power, 20 Hz to 20 kHz.
Common Mode Rejection (CMR): Better than 70 dB from 20 Hz to 1 kHz.
DC Output Offset (Shorted Input): ±10 mV.
Controls and Connectors:
Level: A detented rotary level control for each channel located on the front panel.
Power: An on/off rocker switch located on the front panel.
Mode: A two-position switch located on the back panel below the input connectors which, when turned to stereo, operates the amplifier as two independent channels. When “Bridge- Mono” mode is selected, the amplifier bridges the two output channels for twice the output voltage.
Reset: A front-panel push button used to reset the circuit breaker that protects the power supply.
Sensitivity: A two-position switch located on the back panel next to the Mode switch. Switchable between 1.4 volts for full output into an 8-ohm load (default setting), or a fixed voltage gain of 26 dB. 0.775-volt sensitivity available as a Service Option.
Fault Jack: A back-panel RJ-11 jack that may be remotely monitored to signal amplifier
Fault condition. An LED or other signalling device (not supplied) may be used.
Indicators: (all located on front panel)
Signal: A green LED for each channel which flashes when a very low-level signal (>–40 dBm) is present at input. May be used for troubleshooting cable runs.
Clip: A red LED for each channel which turns on when distortion becomes audible in the amplifier output.
Input/Output:
Input Connector (standard module): One Neutrik® Combo connector for each channel which features a balanced ¼-inch (6.35-mm) phone jack and a 3-pin female XLR connector, in parallel with a barrier strip termination.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance: Nominally 20 k ohms, balanced. Nominally 10 k ohms, unbalanced.
Input Sensitivity: 1.4 volts for standard 1-kHz power, or fixed 26-dB gain. 0.775-volt sensitivity available as a Service Option.
Output Connectors:
Two Neutrik® Speakon® NL4MP (mates with NL4FC) output connectors.
Optional 5-way binding post or barrier strip outputs (in parallel with Speakon® connectors) are available.
DC Output Offset: ±10 millivolts. Output Signal,
Stereo: Unbalanced, two-channel;
Bridge-Mono: Balanced, single-channel. Channel 1 controls are active; Channel 2 should be turned down.
Protection:
CE-Series amplifiers are protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; input overload damage; and high-frequency blowups. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients.
560w at 2ohm, 450w at 4ohm, 275w at 8ohm
Crown MA602
The Macro-Tech VZ Series represents the latest breakthrough in Crown's unending quest to deliver the most power in the smallest package.
The Macro-Tech 3600VZ packs 3,600 watts into a mere 3.5 inches of vertical rack space. The Macro-Tech 5002VZ packs an incredible 5,000 watts into little more than 5 inches of vertical rack space.
400w at 2 ohm, 325w at 4ohm, 225w at 8ohm
Crown K1
No Fan No Noise
Patented BCATM Circuit Design
Unmatched Thermal Efficiency
Superior Energy Efficiency
Sealed Chassis
Superior Sound
Modular Design and Construction for Quick Service
TLC -Thermal Level Control Protection Subtly and Dynamically Reduces Gain As Needed
Automatic Turn-On Diagnostics
Significantly Less Component Degrading Heat Generated
Recessed, Detented Level Controls
750w at 2ohm, 550w at 4ohm, 350w at 8 ohm |
|
|
Apr-06-2003 04:39 
|
|
|
|
|
DJ Tranz
Mafiya Beatts
Registered: Feb 2003
Location: SoCal --- LATA # 99
|
|
|
That really doesn't mean anything! Crown amps are way clearerand cleaner,sharper sounding, more reliable, much better built, and like I said before, they are top choice in their respective classes.
Don't get me wrong, QSC amps are OK, but way too many complaints and returns and two big online stores, including my friend's online store, stopped carrying them.
___________________
Daniel, aka DJ Tranz(MafiyaBeatts-LA,SF)
Rest In Peace Adam 'STARKID' Spears,Thank You For Your Wonderful Music That Will Live On Forever, RIP Buddy...
www.mafiyabeatts.com Vote for Tranz @ The DJ List!
|
|
|
Apr-07-2003 21:17
|
|
|
|
All times are GMT. The time now is 05:10.
Forum Rules:
You may not post new threads
You may not post replies
You may not edit your posts
|
HTML code is ON
vB code is ON
[IMG] code is ON
|
|
|
|
|
|
Contact Us - return to tranceaddict
Powered by: Trance Music & vBulletin Forums
Copyright ©2000-2026, Jelsoft Enterprises Ltd.
Privacy Statement / DMCA
|
