im not too sure. sometimes it happens to me but im actually holding onto the vinyl not the platter. if i hold onto the platter i start to feel and hear a grinding noise which doesnt sound right to me. the way i do it is i hold onto the side of the vinyl while cueing...

___________________
Soundcloud

umm, ok, i thought this was common knowledge (unless me and all my friends are doing it wrong). normally, we first listen to the record and pitch it as well as we can, then we find our cue point, and we "grab" the beat we want to put in, ie. we stop the vinyl with our fingers, i like using that sort of outer rim most vinyls have, we bring the beat in, back and forth synchronized with out live track's beats, and let go when it's time. then we apply corrections/go back to our cue point and "throw our record in" again if necessary.

___________________
check out my guest mix for OndaSonora Podcast (aug.2009)

well if you have slip mats under the record usually you can stop the record and the platter si still spinning.


If I am understanding you right.


I don't really think that stopping the platter does any good to your decks...and any grinding noise = bad news.

If you can't hold the vinyl still as the platter moves (without slowing the platter down significantly) then your slipmats blow ass. If you're using the stock technis slipmats, try using the little plastic sheet between the slip mat and rubber mat.

Basically when I cue I just put the needle down around the first beat (or wherever I want it), and let it play or back spin into place, get it behind the first beat, then press stop and wait for the right time to let it go (or just go ahead and let it play if im beatmatching).

___________________
NEW MIX [Feb/March 2008]

if you're having friction problems, get a grocery bag (plastic) and cut out a 12" circular piece, put it in between the slipmat and the platter, works wonders.

___________________
check out my guest mix for OndaSonora Podcast (aug.2009)

I used to keep the entire platter stopped when cue'ing and just give it a big nudge when the cue-point came. I found that if you have a good pair of slip-mats, grabbing the vinyl on the side and letting the platter spin underneath it is the way to go. Not only does this help with the pick-up time of the record (Time it takes for the record to go from 0 to the designated rpm/pitch) But it helps make sure the beat you're trying to cue stays locked on. (I found that when I used to grab the whole platter, that the needle would skip quite a lot while cue'ing).

___________________
Blithe is a member of the Regressive Party.

Proud member of the Anti-Emo Adolescent White American Sulker Alliance... aka: "Quit crying f**ker and dance."

hm.. I've read on the forums about how you're supposed to stop the vinyl with your finger and let the platter keep running... that's why I brought this up in the first place... so you just put your finger on the side of the vinyl? it just seems that it's easier to stop the whole thing to find the first beat... you know, you can move the platter back and forth a bit so you can hear it.

on a lighter note, there's been no grinding noise at all... oh by the way I'm using 2 numark tt-200's (thanks a ton opianstate) I guess my problem before when I tried stopping just the vinyl and not the platter is I tried lifting up the vinyl a little bit (i figured that's the only way you could stop it). thanks for the advice fellas

omega, you don't stop the platter. you just keep it spinning. You can also move the record back and forth when the platter is spinning, that will make cueing easier. You've seen turntablists, right? And your not gonna break anything. BTW the numark stock slipmats suck so look to upgrade sometime.

___________________

quote:

Make it idiot proof and someone will make a better idiot. He who laughs last thinks slowest!

Come to think of it, I would think it would be sort of tough to always be stopping the platter, never really tried to do so...

I actually used the rubber "slipmats" (cough cough) that came with my Techs for the first few months I was playing, then bought proper felt? ones shortly after. Even when I used the rubber mats, I'm pretty sure that the platter was still spinning underneath them.

___________________
DJ Kibon



Click below to download my most recent trance set:
DJ Kibon - August 2004

Never stop the platter in order to cue up a record. The platter should always be spinning and the record should stop under your fingers if your slipmats are proper. If you stop the platter, you are fighting the turntable motor and will GREATLY decrease it's life.

___________________
Helping girls make bad decisions since 1979

thtas the whole point of mats- to slip over the platter.

when you let go the record, the platter doesnt have to then speed up- it just goes.

you are making things hard for yourself