Here you go!

http://www.turntabletech.com/maintenance.htm

___________________
EDM is not a trend, it's a lifestyle. You either get it or you don't.

Cheers woody,

Need to try and find out where I can that lube or appropriate lube of some kind.

Apply lube everywhere. And lots of it. Come on, you know this stuff, Nelly.

quote:

Originally posted by dj_alfi Apply lube everywhere. And lots of it. Come on, you know this stuff, Nelly.

ha! I don't know what kind of lube to apply.

quote:

Originally posted by DjWoody Here you go! http://www.turntabletech.com/maintenance.htm

Well that seems to be a company that specialises in servicing, not actually telling you how to do it.

I have the official Technics Service Manual at home in PDF - if anyone wants it, just PM me with your email address and I get it over to you when I get a chance.

btw nelly, you need a few different lubes, for instance the center pin bearings use a light "oil" type lube, and the for the tone arm spindles I used a teflon based grease (actually one for road and mountain bikes from a company called Finish Line) as even when it eventually dries, the teflon keeps it running smooth forever.

You'll also need ammeter/ohmeter (or mulitmeter) if you want to do the full service thing and make sure the calibration is all good.

quote:

Originally posted by n3lly ha! I don't know what kind of lube to apply.

Search your feelings and you will know the answer.

quote:

Originally posted by dj_alfi Search your feelings and you will know the answer.

___________________
EDM is not a trend, it's a lifestyle. You either get it or you don't.

quote:

Originally posted by DJ RANN Well that seems to be a company that specialises in servicing, not actually telling you how to do it. I have the official Technics Service Manual at home in PDF - if anyone wants it, just PM me with your email address and I get it over to you when I get a chance. btw nelly, you need a few different lubes, for instance the center pin bearings use a light "oil" type lube, and the for the tone arm spindles I used a teflon based grease (actually one for road and mountain bikes from a company called Finish Line) as even when it eventually dries, the teflon keeps it running smooth forever. You'll also need ammeter/ohmeter (or mulitmeter) if you want to do the full service thing and make sure the calibration is all good.

Sorry only saw this now..

Cheers for the heads up about the lubes. Have a multimeter just need to read what i need to do with it now along with the calibration etc.

Is your service manual similar to this one?

CLICK ME

Thanks for the direction. Keen on messing about a bit more on getting it back in perfect condition. Ever since finishing my Xoxbox I've had a lot more confidence in DIY electrical fixes etc.

Thanks again.

Feelings will hopefully eventually guide me in the way of the better lubes.

quote:

Originally posted by n3lly Sorry only saw this now.. Cheers for the heads up about the lubes. Have a multimeter just need to read what i need to do with it now along with the calibration etc. Is your service manual similar to this one? CLICK ME Thanks for the direction. Keen on messing about a bit more on getting it back in perfect condition. Ever since finishing my Xoxbox I've had a lot more confidence in DIY electrical fixes etc. Thanks again. Feelings will hopefully eventually guide me in the way of the better lubes.

Which multimeter?

quote:

Originally posted by dj christian Which multimeter?

Any that can can do milliamps, resistance in ohms to at least .1 integers and volts. Probably any multimeter will do it.

@nelly - yes that is the book I have.

If you want detailed instructions on maintenance and mods then go to:

http://technics.junglist.pl/

Scroll down a little. The only thing I don't like about this one is they rely on the strobe rather than the multimeter reading on the control pot, but i suppose it will get you very damn close and as long as you match the two tables it's not critical to have them exactly calibrated.

If you want the really in depth guide:



http://music.hyperreal.org/dj/sl1200.html

quote:

Originally posted by dj christian Which multimeter?

It's just a cheap and cheerful one but does everything i need it to do.

quote:

Originally posted by DJ RANN Any that can can do milliamps, resistance in ohms to at least .1 integers and volts. Probably any multimeter will do it. @nelly - yes that is the book I have. If you want detailed instructions on maintenance and mods then go to: http://technics.junglist.pl/ Scroll down a little. The only thing I don't like about this one is they rely on the strobe rather than the multimeter reading on the control pot, but i suppose it will get you very damn close and as long as you match the two tables it's not critical to have them exactly calibrated. If you want the really in depth guide: http://music.hyperreal.org/dj/sl1200.html

You kind sir are a legend. Thanks a million for those links. Plenty of reading for me to do now!! ha!


Actually quick side question for you. I was fixing one of the S bend tone arms on one of mine the other day. Everything went fine and the deck plays perfectly. I am however getting a little ground feedback whenever I though the weight on the headshell. Or the screws that hold the cartridge in place. Nothing that would make me want to tear the whole thing apart but is it pretty much just down to the earth needing to be rewired or is it normal to get a little feedback when touching the metal parts on the headshell ?

Cheers