| BryanMckinlay |
--------------------------------------------------------------------------------
FocusRite Trakmaster
Mic input
Gain: –3 dB to +57 dB
Frequency Response: 0 dB at 20 Hz and –3 dB at 250 kHz.
THD+N: 0.002% (measured at 1kHz using 20 Hz/22 kHz bandpass filter)
Noise: EIN = -121 dB (measured at 57 dB of gain with 150 Ù source impedance and 20 Hz/22 kHz bandpass filter)
Line input
Gain: –10 dB to +10 dB
Frequency Response: 0 dB at 20 Hz and –3 dB at 200 kHz.
THD+N: 0.003% (measured at 1kHz using 20 Hz/22 kHz bandpass filter)
Noise: -94 dBu (using 20 Hz/22 kHz bandpass filter)
Instrument input
Gain: –3 dB to +40 dB
Frequency Response: 0 dB at 20 Hz and –3 dB at 200 kHz.
THD+N: 0.007% (measured at 1 kHz using 20 Hz/22 kHz bandpass filter)
Noise: -94 dBu (using 20 Hz/22 kHz bandpass filter)
Bass EQ (VOCAL mode)
Bell EQ
Frequency range: 50 Hz to 800 Hz
Boost/Cut: +12 / -14 dB
Bass EQ (INST mode)
Shelving EQ
Frequency range: 25 Hz to 400 Hz
Boost/Cut: +12 / -14 dB
Presence EQ
Bell EQ
Frequency: 1.5 kHz
Boost/Cut: +12 / -20 dB
Treble EQ
Shelving EQ
Frequency (VOCAL mode): 10 kHz
Frequency (INST mode): 3.3 kHz
Boost/Cut: +/- 14 dB
Optical Compressor
Threshold (COMRPESSION control): -22 dB (MORE) to +12 dB (LESS)
Ratio (TIGHT switch out): 3:1, soft knee
Ratio (TIGHT switch in): 6:1, hard knee
Attack (PUNCH switch out): 3ms
Attack (PUNCH swtich in): 45mS
Release: 100 mS (FAST) to programme-dependent slow (SLOW)
Makeup gain +20 dB.
Weight
4.5 kg
Dimensions
44 mm (H) x 480 mm (W) x 265 mm (D)
Outputs
Balanced: impedance 50W, nominal level +4dBu
Unbalanced: ground compensated, impedance 75W, nominal level –10dBV
Headroom
22 dB
www.focusrite.com
Studio Projects C1 Condensor Mic
Specifications
Type:
Pressure gradient solid state condenser microphone
Polar pattern:
Cardioid.
Frequency response:
20~20000Hz.
Sensitivity:
14mV/Pa=-37dB(0dB=1V/Pa).
Output impedance:
<200 Ohm.
Load impedance:
>1000 Ohm.
Maximum SPL:
142dB SPL for 1% THD @1000Hz(0dB SPL=0.00002Pa).
Noise:
(Line): 27dB (A weighted)---17dB.
S/N:
77dB.
Power requirement:
48 +/- 4V.
Current consumption:
<2.5mA.
Circuit:
Discrete FET balanced symmetrical output.
Connector:
Gold-plated 3-pin XLR
Size:
dia: 2.1" length: 8.9"
Weight:
26.9oz
Pad:
-10dB
Low cut :
6dB/Octave at 150 Hz.
xcellent package, will include a rack for the pre amp, as well as mic cable and 1/4 inch jacks!
best offer will take this package,
ONLY SERIOUS OFFERS PLEASE this equipment must be gone
also have a almost brand new comuter desk for sale, all steel and glass, L shaped table! (very mint)
cheers for now!
~Bryan Mckinlay |
|
|
