|
Stylus Pressure
|
View this Thread in Original format
| Goldenleon |
How important is it whilst setting the tone arm weight etc?
iv just got a pair of 1210's and the cartridges and styli came with it does not say what the reccomended stylus pressure is.
also anti skate has to be set at 0 iv been told. just wonderuing the reason behind this |
|
|
| djsaryn |
| what type are they? |
|
|
| Goldenleon |
| Ortofon OM Pro S |
|
|
| djsaryn |
| planetdj.com's technical data says recommended is 4 grams. but that seems a bit much. i cant find what mine is, so i have to just go for it. i generally keep mine at about 2.5 and its fine. |
|
|
| Goldenleon |
iv got it set at 2.5 g now
and is it best to leave the anti skate at 0 |
|
|
| auujay |
| quote: | Originally posted by Goldenleon
iv got it set at 2.5 g now
and is it best to leave the anti skate at 0 |
I would use 2.5 or 3 grames, which ever works without skipping.
Yes leave antiskate at 0 if you are back queueing. |
|
|
| tu_face |
ortofon carts i found work best at 3/3.5g.
the stylus pressure range on your carts is 2-5g, so anywhere within that bracket will be ok, but i wouldn't reccommend you go over 4g as record wear starts coming into play :) |
|
|
| DjVash |
| quote: | Originally posted by Goldenleon
iv got it set at 2.5 g now
and is it best to leave the anti skate at 0 |
No. Your anti skating needs to be identical to your stylus pressure, so in your case, set it to 2,5. EXCEPT when you're scratching like hell! Then set it to 0.
Furthermore I would recommend 3,5g for Ortofon cartridges. Set the anti skating to 3 (an SL doesn't go any higher :D) |
|
|
| 6iki_Snake |
What i learned was too set the anti-skating to the same amount of g. as the tonearm weight itself. Mines are both at 3g.
[offtopic]
btw hi all, this is my first post on this forum :happy2: Ive been reading and lurking for a very long time. Finally registered. Havent been able to notice a introduction part of the forum somewhere ...so here is my introduction. :stongue:
[/offtopic] |
|
|
| tu_face |
| quote: | Originally posted by DjVash
No. Your anti skating needs to be identical to your stylus pressure, so in your case, set it to 2,5. EXCEPT when you're scratching like hell! Then set it to 0. |
i would always keep the anti-skate at 0, simply because of back-cueing. :) |
|
|
| Liam |
| Anti-skate should be set at 0!!!! |
|
|
| auujay |
OK let me get detailed with the anti-skate.
The true way to set it for normal (read forward only) playing is to get a one sided promo or a record that has a blank side. But the blank side up and put the needle in the middle now adjust the antiskate so the needle stays in the middle and does not move to the inside (spindle) or outside (edge).
The easier way to set anti-skate for normal (read forward only) playing is to just set the antiskate to the same as the stylus pressure.
If you are going to be backqueuing/scratching/(basically DJing) than you want to antiskate set to 0. It makes sense if you think about what antiskate does. When a record is playing the clockwise motion is causing extra pressure on the left side of the groove (the needle is pushed towards the spindle by the groove). To counter this force (or "skateing") the anti-skate applies pressure to the outside ot the record (or the right side of the groove). When properly set up these two forces will mostly balance out when the record is playing forword (going counterclockwise). However, when the record is going in reverse the opposise force is acting on the needle, it is getting pushed to the outside of the record by both the groove and the anti-skate. If you have your antiskate set to a positive number, this may explani why most of your skips happen when you backqueue. |
|
|
|
|
