|
my integrated sound card... (pg. 2)
|
View this Thread in Original format
| sw1 |
| quote: | Originally posted by xstalkrx
one RCA cable cannot give me sound from both channgels on my mixer. |
:conf: Not sure what you mean by both channels on your mixer. Is that left channel and right channel you're talking about? There is only one output from your mixer anyways.
The ground loop isolator is a stereo RCA cable (2 channels).
Get 2 (two) Y-cables to split the master out on the mixer. One for left, one for right. |
|
|
| xstalkrx |
| quote: | Originally posted by sw1
:conf: Not sure what you mean by both channels on your mixer. Is that left channel and right channel you're talking about? There is only one output from your mixer anyways.
The ground loop isolator is a stereo RCA cable (2 channels).
Get 2 (two) Y-cables to split the master out on the mixer. One for left, one for right. |
ya i was confused there for a sec. ok i am picturing how it all works now.
any experience with these ground loop isolators? do they block out all humming? |
|
|
| Orbital32 |
| try googling some of these questions. I'm sure your results will be alot faster then you posting the question. |
|
|
| sw1 |
| quote: | Originally posted by xstalkrx
ya i was confused there for a sec. ok i am picturing how it all works now.
any experience with these ground loop isolators? do they block out all humming? |
They do reduce the humming quite a bit. You'd have to judge that for yourself. With the Y-cable though, you'll also end up with a direct connection from your receiver to your computer. That may introduce some hum too at either end. It's better if you had a master out and a tape out on your mixer. Then you wouldn't need the Y-cables. |
|
|
| xstalkrx |
I'm just going to buy a new mixer to solve my master out problem. Probably about time i had a three band EQ anyways. :/
I was looking at the Pioneer DJM-300 as my next mixer? Any feedback on this mixer?
A employee at Guitar Center said that an integrated sound card is going to make my recordings sound like regardless of any ground loop isolator i use. He says the humming has nothing to do with any ground. He says I will need a decent sound card before getting a clean recording.
Thoughts on this? |
|
|
| Orbital32 |
| well tell that guy that i said that he's a ing idiot. Why do i have a ground loop isolator on my mixer going to my comp? for the same reason i have on one my car. It takes the humming out....like its suppose too. |
|
|
| xstalkrx |
| What kind of computer do you have orbital? What are the specs? I have a 2.7 ghz processor if that has anything to do with recording...and its a cheap emachines comp. |
|
|
| trancecadet |
how have you wired up your ground loop for the laptop Orbital?
@ xstalkrx... CPU speed means nothing really when recording. I used to use an old K6-2 450 to record my sets.. But a good CPU helps for production.. Your PC is an Intel P4 or Celeron.. Hopefully a P4 since they are better. No big deal though :)
oh and i feel like braggin.. I have.. Intel 1.4ghz lappy, AMD 1.5 @ 2.2ghz watercooled (almost complete), AMD 1.4 @ 1.8ghz, Intel Dual P3 550's plus another 2 Intel P4's half built.. :D I work for a PC repair company ;) |
|
|
| Derivative |
| quote: | Originally posted by xstalkrx
A employee at Guitar Center said that an integrated sound card is going to make my recordings sound like regardless of any ground loop isolator i use. He says the humming has nothing to do with any ground. He says I will need a decent sound card before getting a clean recording.
Thoughts on this? |
no hes right in a way but he hasnt explained it very well though.
if your mixer doesnt have an onboard preamp then you need to use a DI box or external preamp between the turntable/mixer and in the input on your soundcard. otherwise the signal wont be hot enough when recording and you'll find you have to amp up the signal loads post recording which will increase the noise floor as well as peak volume. this often results in audible humming.
even if that isnt taken into account what kind of analogue to digital converters are there on an onboard soundcard?! you are never going to get 24 bit/96 khz recordings from a mini TRS jack.
an m-audio audiophile 24/96 is pretty cheap, has 2 analogue RCA inputs and it can record at 24 bit and 96 khz. the A/D converters arent too shabby either. one of those would solve all of your problems pretty much.
but yea. i fail to see how recording through a mini TRS line input is ever going to get you the kind of bit for bit recording you are going to get with a proper 24/96 recording interface... |
|
|
| xstalkrx |
| quote: | Originally posted by Derivative
no hes right in a way but he hasnt explained it very well though.
if your mixer doesnt have an onboard preamp then you need to use a DI box or external preamp between the turntable/mixer and in the input on your soundcard. otherwise the signal wont be hot enough when recording and you'll find you have to amp up the signal loads post recording which will increase the noise floor as well as peak volume. this often results in audible humming.
even if that isnt taken into account what kind of analogue to digital converters are there on an onboard soundcard?! you are never going to get 24 bit/96 khz recordings from a mini TRS jack.
an m-audio audiophile 24/96 is pretty cheap, has 2 analogue RCA inputs and it can record at 24 bit and 96 khz. the A/D converters arent too shabby either. one of those would solve all of your problems pretty much.
but yea. i fail to see how recording through a mini TRS line input is ever going to get you the kind of bit for bit recording you are going to get with a proper 24/96 recording interface... |
Ok so that audiophile product is like an external sound card? I'll plug my 1/8 jack into this audiophile and then the audiophile connects using USB ports? And I get very clean recordings without having to use ground loop isolators? Or are the ground loop isolators still recommended?
Well after looking at the pics it only has 1/4 inch jacks. |
|
|
| Orbital32 |
| quote: | Originally posted by trancecadet
how have you wired up your ground loop for the laptop Orbital?
@ xstalkrx... CPU speed means nothing really when recording. I used to use an old K6-2 450 to record my sets.. But a good CPU helps for production.. Your PC is an Intel P4 or Celeron.. Hopefully a P4 since they are better. No big deal though :)
oh and i feel like braggin.. I have.. Intel 1.4ghz lappy, AMD 1.5 @ 2.2ghz watercooled (almost complete), AMD 1.4 @ 1.8ghz, Intel Dual P3 550's plus another 2 Intel P4's half built.. :D I work for a PC repair company ;) |
i have a 933mhz PIII. but like it was stated CPU means nothing to the soundcard. I have 2 different sound cards attached, one is a Hercules GTXP and the other is a Hercules DJ console. I have the RCA jacks coming from DN-x1500 mixer to the isolator to my RCA inputs of my soundcards. The only i was able to get rid of the hum was through the isolator, no volume, adjusment of the location fo the cords, or anything else was able to take it out. What i might do, since the Denon Dn-x1500 has a co-ax digital out, that would make it clearer...and since the DJ console everyting at 48Khz @ 24bit, the sound should come out great! |
|
|
| trancecadet |
| I have a GTXP.. brilliant soundcards.. |
|
|
|
|
